Oil change problem ?

bigdog · 08-11-2021, 11:04 AM

I just went to change my oil in my 4.3L MerCruiser engine.....

I've done this before using a hand pump I purchased at boat supply store.
The pump has an inlet hole where you connect a plastic tube, the other end over the dipstick (yes I removed the dipstick). The other inlet hole you connect another plastic hose, where the pumped oil will come out.

The issue is, when I start pumping, no oil comes out, it's like there's something wrong with the pump ? I've only used this pump 'one' time, in the past, so confused ?

As an alternative solution, is there an electric pump or a pump that can be attached to my electric drill to pump out the oil ?

Thanks for you comments, much appreciated !

Blue Thunder · 08-11-2021, 12:02 PM

I bought one of these about six years ago. It makes everything so easy and cleanup is quick. I use it on the boat, jetski, lawnmower and snowblower….

https://www.amazon.com/Jabsco-17850-.../dp/B001CX0WX4

Woodsy · 08-11-2021, 12:08 PM

If its something like this, you need to make sure all the connections are tight and its not leaking vacuum anywhere. I have had mine for years and it works mint!

https://www.amazon.com/Mityvac-Fluid...701622&sr=8-56

Woodsy

Descant · 08-11-2021, 12:35 PM

It sounds like an air leak someplace. Perhaps a split in the plastic tubes?

8gv · 08-11-2021, 01:03 PM

You may have lost the washer that goes in the female screw on fitting.

Also, these work best with “run around the lake” hot oil, not “let it idle for a while at the dock” warm oil.

BroadHopper · 08-12-2021, 07:26 AM

I fitted a rubber hose to the drain plug on the oil pan. The rubber is long enough to attach to the transom. If the boat is out of the water, I would run the hose through the drain in the transom and remove the oil. If the boat is in the water I would fit the hose to a drain pump. Pretty slick!

08-11-2021, 11:04 AM	#1
bigdog Senior Member Join Date: Apr 2006 Location: Central MA-Gilford Posts: 1,450 Thanks: 345 Thanked 122 Times in 97 Posts	Oil change problem ? I just went to change my oil in my 4.3L MerCruiser engine..... I've done this before using a hand pump I purchased at boat supply store. The pump has an inlet hole where you connect a plastic tube, the other end over the dipstick (yes I removed the dipstick). The other inlet hole you connect another plastic hose, where the pumped oil will come out. The issue is, when I start pumping, no oil comes out, it's like there's something wrong with the pump ? I've only used this pump 'one' time, in the past, so confused ? As an alternative solution, is there an electric pump or a pump that can be attached to my electric drill to pump out the oil ? Thanks for you comments, much appreciated ! Last edited by bigdog; 08-11-2021 at 11:07 AM. Reason: spell

08-11-2021, 12:02 PM	#2
Blue Thunder Senior Member Join Date: Apr 2004 Location: Eastern MA & Frye Island/Sebago Lake, Maine Posts: 951 Thanks: 252 Thanked 351 Times in 158 Posts	I bought one of these about six years ago. It makes everything so easy and cleanup is quick. I use it on the boat, jetski, lawnmower and snowblower…. https://www.amazon.com/Jabsco-17850-.../dp/B001CX0WX4 __________________ " Live for today because yesterday is gone and tomorrow may never come"

08-11-2021, 12:08 PM	#3
Woodsy Senior Member Join Date: May 2004 Location: Weirs Beach Posts: 1,966 Thanks: 80 Thanked 980 Times in 440 Posts	If its something like this, you need to make sure all the connections are tight and its not leaking vacuum anywhere. I have had mine for years and it works mint! https://www.amazon.com/Mityvac-Fluid...701622&sr=8-56 Woodsy __________________ The only way to eliminate ignorant behavior is through education. You can't fix stupid.

08-11-2021, 12:35 PM	#4
Descant Senior Member Join Date: Mar 2006 Location: Merrimack and Welch Island Posts: 4,378 Thanks: 1,353 Thanked 1,628 Times in 1,060 Posts	air leak? It sounds like an air leak someplace. Perhaps a split in the plastic tubes?

08-12-2021, 07:26 AM	#6
BroadHopper Senior Member Join Date: Oct 2004 Location: Laconia NH Posts: 5,582 Thanks: 3,223 Thanked 1,106 Times in 796 Posts	Old school. I fitted a rubber hose to the drain plug on the oil pan. The rubber is long enough to attach to the transom. If the boat is out of the water, I would run the hose through the drain in the transom and remove the oil. If the boat is in the water I would fit the hose to a drain pump. Pretty slick! __________________ Someday may never be an actual day.

The Following User Says Thank You to Woodsy For This Useful Post:
Cal Coon (08-13-2021)

08-11-2021, 01:03 PM	#5
8gv Senior Member Join Date: Jan 2012 Posts: 2,107 Thanks: 64 Thanked 747 Times in 481 Posts	You may have lost the washer that goes in the female screw on fitting. Also, these work best with “run around the lake” hot oil, not “let it idle for a while at the dock” warm oil.